Snow removal or snow clearing is the job of removing snow after a snowfall to make travel easier and safer. This is done by both individual households and by governments and institutions.
The de-icing of roads has historically been accomplished by snowplows or specially-designed dump trucks that spread salt, often mixed with sand and gravel, onto slick roads. Rock salt is normally used because it is inexpensive and readily available in large quantities. However, brine freezes at −18 °C (0 °F), and so it is ineffective at these low temperatures. It also has a strong tendency to cause corrosion, rusting the steel used in most vehicles and the rebar in concrete bridges. More recent snowmelters use other salts, such as calcium chloride and magnesium chloride, which not only decrease the freezing point of water to a much lower temperature A mixture of some selection of these organic compounds with a combination of salts results in a substance that is both more easily spread and more effective at lower temperatures (−34 °C or −30 °F).
Since the 1990s, use of liquid chemical melters has been increasing, sprayer on roads by nozzles instead of a spinning spreader used with salts. Liquid melters are more effective at preventing the ice from bonding to the surface than melting through existing ice.
Several proprietary products incorporate anti-icing chemicals into the pavement. Verglimit incorporates calcium chloride granules into asphalt pavement. The granules are continually exposed by traffic wear, and release calcium chloride onto the surface. This prevents snow and ice from sticking to the pavement Verglimit SA, Capabilities of Verglimit, http://www.verglimit.eu/en_capabilities.php, Sep 20, 2010, retrieved 12/14/2010
Cargill SafeLane is a proprietary pavement surface treatment that absorbs anti-icing brines, to be released during a storm or other icing event. It also provides a high-friction surface, increasing traction.Cargill, Inc., SafeLane Surface Overlay, http://www.cargillsafelane.com/, retrieved 12/14/2010
In Niigata, Japan, relatively inexpensive hot water bubbles up through holes in the pavement to melt snow, though this solution is only practical within a city or town. Some individual buildings may melt snow and ice with electric power heating elements buried in the pavement, or even on a roof to prevent Ice dam (roof) on the Roof shingle, or to keep massive chunks of snow and dangerous icicles from collapsing on anyone below. Small areas of pavement can be kept ice-free by circulating heated liquids in embedded piping systems.
Most snow removal by individuals is clearance of driveways and walkways. After heavy snowfalls, snow may be removed from roofs to reduce the risk of structural damage due to the weight.
In places with light snow, brooms or other light instruments can be used to brush off snow from walks and other surfaces. In regions with more precipitation, snow is commonly removed with snow shovels, a large lightweight shovel used to push snow and lift it, and snow scoops or sleigh shovels, a large and deep hopper-like implement fitted with a wide handle and designed to scoop up a load of snow and slide it on any slippery surface to another location without lifting. Other tools include snow pushers and shovels with one or more wheels.
Shovelling entails a considerable amount of physical effort and can strain the back and the heart. Each year many senior citizens and middle aged persons die from heart attacks while shovelling snow.[http://shovler.com/blog/dangers-of-shoveling-snow/ Dangers of Shoveling Snow]
Snow blowers are often used by people unwilling or unable to perform this labour, people with large driveways or other substantial surfaces and people who live in areas with long lasting winters with large amounts of snowfall. Others may hire a contractor with a plow bearing truck or a shovel.[http://thedailyreview.com/news/snow-slams-area-slick-roads-lead-to-travel-troubles-1.611110 Snow slams area: Slick roads lead to travel troubles - News - Daily Review] In some jurisdictions, motorists who fail to clear snow from their vehicle entirely may be fined.[http://www.nj.com/gloucester/index.ssf?/base/news-14/1265779531326870.xml&coll=8 A clean car is safe Ð and legal - NJ.com] Others may be more thorough in this process.
In some urban residential areas with curbside parking, residents Parking space reservation in snowstorms so they can reclaim their space upon their return.
One example of the longstanding debate over the obligation of snow removal comes from the Czech Republic. In Prague, evidence of such a duty is documented since 1838.Pavel Fastr: ''Zákon o pozemních komunikacích s komentářem a vyhláškou.'', Praha, Linde, repeated editions since 1997 The decree of the government of the Protectorate of Bohemia and Moravia No. 1/1943 Sb. said that sidewalk cleaning in residential areas of municipalities with more than 5000 inhabitants, of district cities and of other specified municipalities is a duty of the owner or user of the contiguous land. The municipality was empowered to undertake this duty at the expense of the contiguous land owner. The Czechoslovak Road Act No. 135/1961 Sb. (§23) adopted such legal regulations for all municipalities, but municipality offices could modify them. The new Road Act of the Czech Republic, No. 13/1997 Sb. (§9 art. 4) left this enactment in place and stated that maintenance of a road, path, track etc. is an obligation of its owner without any exception. Despite this, §27 art. 4 attached to the owner of contiguous land the liability for harm caused by defects of cleaning. In its 2002 and 2003 annual reports, the Ombudsman#Czech Republic made a claim for there being a discrepancy between the theoretical and the practical interpretations of the act and recommended that an unequivocal formulation be enacted. This discrepancy was repeatedly handled by the courts, and the Supreme Administrative Court on 27 June 2005 and the Constitutional Court on 3 January 2007 each stated that the cleaning duty results indirectly from the stated liability for harm. Those who impugn the duty argued that it is a residue of feudal corvée or of the totalitarian Nazi and communist regimes, that nowadays, compulsory labour mandated by law is in conflict with the Charter of Fundamental Rights and Basic Freedoms and that systematic municipal cleaning is more effective than cleaning by individuals. On 6 December 2007, the Senate of the Czech Republic proposed at the instance of its Constitutional Committee to remove the controversial article from §27 of the Road Act of 1997. The Czech Government gave support to it by a narrow majority. In a previous vote and after heated debate, the Chamber of Deputies of the Czech Republic had sanctioned this change by a margin of 116 to 31 amongst the 190 members present. Since 16 April 2009, the changes made by Act No. 97/2009 Sb. mandate that sidewalk cleaning is an obligation only of the owner of the walkway or road, i.e. generally the municipality. Despite the abolition of the duty, many people, including its opponents, declared that they will continue the winter cleaning of municipal sidewalks and paths, but instead will do so voluntarily and on their own behalf.
As was mentioned during the discussion in the Parliament of the Czech Republic in a statement by the Czech Association of Cities and Municipalities, a similar duty belongs to owners of contiguous land exists in many other modern countries, e.g. Austria, France, the United States and some cities in Bavaria.
In many high elevation or heavy snow accumulating areas, companies with snow removal equipment offer to provide services to remove the snow. Contractors may work on a per-time basis, full season contract, or will-call status. Per-time service (or per-push) is usually invoiced monthly and customers will be charged for each time services are provided. Some companies will charge per-time and per-inch where the depth of the snow is even taken into account. A full season contract is quoted and paid upfront at the start of the season and services will be provided automatically according to the contracted terms. Terms may sometimes differ between companies. For example, some full season contracts will expire after a certain amount of trips where others are unlimited. And finally, will-call service is where the client makes contact with the snow removal company to initiate a single clearing. This is not an automatic service and charges are usually higher for will-call jobs.
Snow removal services may include driveway and parking area snow removal, walkway and deck handwork, and occasionally roof clearing. Contractors use hand shovels, walk behind snowblowers (or snow throwers), truck plows, skid-steers, light-weight tractors, and heavy front-end loaders. Many times, these machines will require use of tire chains to perform their tasks. Snow may be pushed by plowing methods or blown to an area of the property by snowblowers. Contractors may apply sand or salt in some locations to help melt ice accumulations.
Many snow removal contractors will require installation of snow poles or snow staking along the driveway. This is to keep equipment out of the landscaping and to help identify the perimeter of an area.
In cities where snow steadily accumulates over the winter it is also necessary to remove the piles of snow that build up on the side of the roads known as windrows or snowbanks. There are a number of methods of doing this. ''Pulling snow'' is done when temperatures rise high enough for traffic to melt snow. The windrows are then broken up and spread over the road. ''Casting'' is the moving of snow by means of a shovel or plow to nearby public lands. On boulevards or highways ''winging back'' is done, which consists of pushing the snow banks further from the road. The most expensive option, but necessary when there are no nearby places to dump the snow, is to haul it away. This is most often done by large self-propelled snowblowers that gather the piles of snow at the side of the road and load it into dump trucks. The snow is then dumped on the outskirts of town, or in a nearby lake, river or harbor. (Some jurisdictions have banned dumping snow into local bodies of water for environmental reasons - modern roads can be contaminated with melting salt, motor oil, and other substances.) Snowmelter may be cheaper than moving snow, depending on the cost of fuel and the ambient temperature.[http://www.city.toronto.on.ca/transportation/snow/torontomelt.htm City of Toronto: Transportation Services - Snow management]
The windrows created by the plows in residential areas often block driveways and imprison parked cars. The snow pushed there by any plow is a dense, packed version of "normal" fallen snow. When the temperatures are significantly below freezing this packed snow takes some of the characteristics of solid ice. Its removal is nearly impossible without mechanical means.
The largest roads and highways are the first to be cleared; roads with steep hills or other dangers are also often a priority. Streets used by buses and other mass transit are also often given higher priorities. It often takes many hours, or even days, to cover every street in a city. In some places, a snow emergency will be declared, where automobile owners are instructed to remove their vehicles from the street (or one side of a street). If cars are in the way when the plows come around, they may be hauled away by tow trucks. Some communities have standing snow emergency rules in winter, in which vehicles may not be parked on streets overnight, whether it snows or not. After smaller snow storms only main roads are cleared while residential ones are left to be melted by passing traffic. Decisions on immediate removal versus "natural melting" can be hard to make because the inconvenience to citizens and the economy in general must be weighed against the immediate effect on the snow removal budget at that particular moment in the season.
In large cities with heavy snowfalls like Montreal and Ottawa, the snow clearing expense for each season is an important part of the seasonal public works budget and each snow storm provokes a major logistical operation involving thousands of employees working in shifts 24 hours a day. The effort can vary greatly depending on the amount of snow. Montreal gets about 225 cm of snow each winter and spends more than $158 million Canadian (2013)[http://ville.montreal.qc.ca/pls/portal/docs/page/service_fin_fr/media/documents/budget-2013-ACTIVITES.pdf Montreal 2013 Budget] each year to remove it. Toronto, with about 50 per cent more population and 28 per cent more road surface, gets only 125 cm of snow a year and spends about half that.[http://www.canada.com/finance/moneywise/story.html?id=2fe90713-1df8-4f24-9a00-fdbeb648426a Cost of Snow (December 24, 2004)]
Snow removal impacts the design of city infrastructure. Where possible, street boulevards are wider to accommodate the windrows and sidewalks are not right next to the street. Fire hydrants will have tall flags to locate them under the windrows. Reflective traffic lane markers embedded in the roadbed is not possible (or much harder) due to risk of damage by plows. Access to snow dumping locations (e.g. ravines) by heavy equipment is also planned.
It is estimated that Canada spends $1 billion annually on snow removal.[http://www.thecanadianencyclopedia.com/en/article/ice/ Ice] The employees who do this work are generally the same workers who do road maintenance work during the summer months, but in some US cities garbage trucks are also equipped with plows and used for snow removal. Many smaller US communities sign contracts with insurance companies, under which the insurance company assumes the risk of a heavy winter. The insurance company of course sets the rates such that averaged over time they will make a profit; the town is willing to overpay for snow removal in mild winters in order to avoid the risk of running dramatically over budget in the occasional severe winter.
Large organizations such as university and airports also often have their own mechanized snow clearing force. Public transit systems generally clear bus stops while post offices clear around Post boxes. Railroads have their own snow clearing devices such as rotary snowplows.
Airports, with their associated runways, taxiways and ramp areas are an exception to the use of salt, as the metals used in aircraft construction will corrode causing safety issues.
A snow dump site is a location where snow is dumped as a part of the snow removal process. Designated sites are sometimes required to prevent water and ground pollution because the snow collected on roads typically contain a variety of grit, de-icing chemicals, vehicle fluids, engine emissions, and litter. Some pollutants become diluted and wash away with the melt-water and some concentrate at the dump site."Evaluation of Snow Disposal into Near Shore Marine Environments" Alaska Department of Environmental Conservation. June 2006. https://dec.alaska.gov/water/wnpspc/stormwater/docs/adec_snow_disposal_evaluation..htm.pdf Dumping into fresh water is "...almost universally prohibited due to the serious impact that deicer salts can have on freshwater aquatic life." In the United States dumping snow into water bodies is not specifically prohibited by the Clean Water Act or the Ocean Dumping Act. The states and local governments determine their own dumping policies.
Snow dump site selection is based on the availability of suitable land and pollution prevention factors that may include distances from lakes and streams, installation of silt fences, soil and aquifer type, and other factors. Some sites may use filters and settling ponds to help prevent the pollution from spreading. Occasionally an excessive amount of snow must be dumped and is sometimes allowed to be legally dumped into water bodies on an "emergency only" basis.
Chemical treatment materials include:
In the European Union, 98% of chemical treatment materials used in 2000 were sodium chloride in various forms. It is effective down to −5 °C, at the most −7 °C. For colder temperatures, calcium chloride (CaCl2) is added to NaCl in some countries, but deployment is limited as it costs about 6 times as much as sodium chloride. Other substances were used rarely and experimentally. Alternative substances (urea, alcohols, glycols) are often used at airports.Karel Melcher: [http://ekolist.cz/zprava.shtml?x=49570 Posypové materiály pro zimní údržbu komunikací v ČR a v zemích EU] (Winter road maintenance spreadings in the Czech Republic and in EU countries), Ekolist.cz, 3. 12. 2001 In recent years, Geomelt, a combination of salt brine and beet juice that is otherwise considered a waste product has been used for pretreatment. In Wisconsin, USA, surplus brine from cheese making has been used for this purpose.
Inert spreadings can be:
The choice of treatment may include consideration of the effect on vegetation, pets and other animals, the local Drainage basin, and effectiveness with regard to speed and temperature. Some chemicals can degrade concrete, metals, and other materials. The resulting meltwater and slush can cause frost heaving if it re-freezes, which can also damage pavement. Inert materials can damage vehicles and create dust.
As an example, in the Czech Republic during the winter season of 2000/2001, net material expenditure for road treatment was: 168 000 tonnes of salt (mostly NaCl), 348 000 tonnes of sand and crushed stone and 91 000 tonnes of other materials like slag. In Ireland, the annual expenditure of salt was 30 000 tonnes. Switzerland reports their annual expenditure as 600 grammes of salt to every square metre of roads on average.
Chemicals may react with infrastructure, the environment, and vehicles. Chlorides corrode steel and aluminum in reinforced concrete, structures and vehicles. Acetates can cause asphalt stripping, weakening the bond between asphalt binder and aggregate. Sand and grit can clog pavement joints and cracks, preventing pavement from expanding in the summer and increasing stress in the pavement.